dodge.pickup.olympus.cx

Hello, everyone! I have done some basic mods to my truck (fuel screw 2 and 3/4 turns, smoke screw bottomed, star wheel bottomed, grinded fuel pin). Well I have decided to take my high idle screw out (which i did) and am having issues getting my throttle cable to tighten up so i can get it to...

I have a 90 dodge and the 727 3 speed is starting to slip. Has anyone swaped in a 518 with overdrive? I'm just trying to make sure it will work befor I do it. Any advice??

Hi, im looking for a way to stiffin my rear suspension on my '92 w350. A couple years back i put a cannonball hay/dump bed on my truck and it sits the rear down to the overloads, so when i drive down my dirt road the overload springs make this loud CLACK CLACK CLACK sound when i hit bumps. Almost...

I have a 92 5.9 transplanted into a restomod 56 Diamond T. I have a 40 gallon sadle tank with the fuel line coming out the top of the tank and an internal pickup tube that is about .25" off the bottom of the tank. Other than that and the hose going to the lift pump everything is stock. It will...

I am contemplating whether to make my crewcab a dually or single wheel. I am going to convert it to 4x4 with a ppump and 47rh. but i am worried if i do a stock lift i will want more. and i do i dont think I could fit anything bigger then a 235 16 in the back. so i would have to run spacers and that...

here are some pictures of the build of the new bumper for my first gen. hoping to have it done tomorrow. i will also be building a brush guard, and a matching rear bumper. Image: http://i77.photobucket.com/albums/j70/ramchargermann/p_00161.jpg Image:...

i have a 1990 non intercooled and just was wondering what the best route would be, try to find a 1992-1993 dodge intercooler or and psd intercooler outta the 7.3s. just seein what everyones opinions were and if they knew where i could start with one thanks,

wat would be the best way to set up my twins i have a hx35w with a ht3b

After making pump adjustments should I be worried my Cummins may run away at any time? This is my biggest concern... Every time my idle seems high I get a little worried...

So I have an opportunity to get an Eaton Fuller FS 4505B 5spd tranny from a UPS truck. Im buying the 12v p-pumped Cummins from the truck and am considering picking up the 5spd as well. The tranny is rated for somewhere around 1400lbs of torque :drool2:. Does anyone know what kind of job its...

So I have to get my old girl tested before I can register her. She's stock so far(besides guages), Any tricks or additives you guys recommend? If I fail, could I detune it? (adjust fuel pin to shallowest setting) I vaguely remember my grandpa telling me a story about one of his trucker buddies...

:banghead:sadly my truck blew the head gasket the other day :doh:. anyone know of a good place to get one. i want to get good one since i now have to do the job. any input would be great. thanks.

Ok i have a w-250 that the frame is shot as well as about well everything but the powertrain. I just found a d-350 that is the opposite powertrain is shot but body and frame are in mint condition. My question is can i take my power train and put it under the 2wd to make it a 4x4 without...

ive got a knock on #6 and its been there ever since i purchased truck in may i thought it was a injector changed them same thing i then thought maybe overhead needed adjustment did that as well still knock i can take a broom handle while its running and its in #6 cylinder we think its a piston pin?...

Hey guys i installed a 5.9 n my 93 ford f-350. I got it running this spring but one thing i never got right was the water temp sending unit. I installed it right behind the intake air temp sensor. (there is a port right behind it i went into) but my gauge don't work. so i am guessing i went to the...

Does anyone know the color codes for the wiring for the radio in the '92's? I guess it should be easy enough to find the ground, batt + and ign + but would like to know the speaker colors.

Hey guys I think my thermostat is bad on my truck due to the fact that the temp fluctuates pretty easily when I step on the gas. it is a 90 with 350 on it. I live in texas and was wondering what degree thermostat I should get, I don't care about performance, just diesel mileage. Thanks guys

I want to do the piston pump on my truck but I want to do the one off of a 95 or 96 cause they are saposed to put out more pressure so I know I would need to regulate it but I need to know what is a safe max pis to push to the ve and if in wrong what pump to rub for the most psi

I WANT ONE! i know i saw a thread about it a while back but cant seem to find it again.is there any one out there with one? and if this is a dumb idea dont beat my :spank:

I've heard of people putting twin p-pumps and dual cp3's but has anyone put twin VE's on a street truck?