dodge.pickup.olympus.cx

looking for someone that has put hyd. brake booster on 1992 w250 cummins

Did the cummins come with a catalytic converter in 1993.

i mounted my hx 35...come out of a 99 manual it has the cast elbow witht he 5 bolts my question is what are you guys doing to mate the 2nd gen dowpipe to a 1stgen exhaust. im looking to get a 4inch exhaust but looks like a 4inch down pipe might be tight. but after that im curious if you guys are...

I can get a like new ats 3 piece manifold off a 99 24v for very cheap but will it bolt up? Are they the same

I figure nobody cares, but I have an old 92 W250 automatic. It's a little rusty, the front fenders are sagging a tad, and the factory clear coat is fading off her red facade..... I had to make a TPS (thanks guys!), and had to put on a pull out shut down cable. I installed an M3 fuel pin today...

What air intakes fit our manifolds? I think 2nd gen without the front brace, any thing else, with a 3 " intercooler hose size?

I am sticking a cummins in a 66 f100 with an air ride. The fuel cell is located behind the frame notch which is rather large and the fuel lines will have to follow the frame uphill quite a ways and go back down before heading to the motor. Would this be a problem for the stock mechanical pump or...

Ok so need to put a goose neck hitch in the truck. My question is this. How are yall doing it? There is no space between the bed and the frame. I called one company that does it locally and it is gonna be 450 for a standard non flip down ball. Thought that was a bit HI!!!

has any one out there put a hydra. brake booster on a 1992 w250 with Cummings i have heard of it being done

Any recommendations on a clutch brand? Decided that since the transmission is out for the rear main seal, might as well as replace the clutch. THanks in advance.

i just bought a 1992 w250 it had the 4 post door mirrors on the truck the kid i got it from patched up the holes he was going to put smaller mirrors on. so i now have the truck and bought the smaller door mirrors off of rock auto and i need help with the measurments on where exactly they go on the...

my shifter bushing took a crap the other day and it's a pain in the arss to find the right gear now. does anyone got a part number for a bushing kit? i've tried every parts store in my area and none of them can come up with anything.

My head lights went out the other morning for about a minute. nothing else went out. I left the low beams on and didn't have another problem. is there a reason why they would go out and come back on like that?

How do I take the slack out of my steering in w350. The shaft seems fine but there is alot of play at the pitman arm. Any help would be great. Thanks

When I start my truck in the morning the oil light comes on and stays on untill i rev the motor up. Is this somthing I need to worry about?

I turned on the wipers the other day and of course they wouldnt turn on. I tested the wires going to my wiper motor and two of them have power when on high and low settings. the green wire, and the red and yellow wire dont have power. I put a new wiper motor on and it wouldnt work either. Any...

how much would a set of stock fender well trim be worth in good shape?

im new here to the ve trucks, i have a very potent 24v and a mild 12v, but working on a buddy of mine's ve truck and hes looking to get 500 or over to do some local pulling with us, and well to just have some fun..... ive allready got the turbo and downpipe, know im doing to do and exhaust...

Putting on a super s300 which is only a 57 mm and was thinking of what injector size to go with. Wanted to go with a 100hp injector but would that be to much for my ve without a airdog?

If you saw my previous thread, you may have realized I'm a new first gen owner, and new to the cummins world all together. looks as if its pissing fuel from around the injectors... Is this a common problem? Do the injectors have like a o-ring seal or something that needs to be replaced or are...