dodge.pickup.olympus.cx

Searched for an hour. Seems it could be tps or a relay in the steering column. It shifts fine when engaged and the truck is otherwise in good to excellent condition (except a little clunk when shifting to R). Any thoughts? 91 (not 91.5) w250 Diesel 119,000 miles

PLEASE HELP....CAN ANYONE HELP ME OUT? I have a 1992 dodge. and it won't run good. It runs very rough, and it won't idle. Engine dies with nothing down on peddle. Floored it blows out some white smoke and does not rev very high. As I keep it floored, the rpms diminish and when I let off and...

I have checked and double checked all connections, the motor is in an 04 F350 so I would doubt a rusty fuel line. I can turn the truck over and get fuel shooting out of the back of the injectors. The truck will try to start, then it will go back to just cranking. If I crack the injector lines...

does anybody know if and where we can get jake brakes for our trucks? theres one on youtube that sounds just like a big rig. trying to find something like that

Does anyone has any pictures of a ground pin? Did you get it done at a machine shop or by yourself?

Can you remove the plastic washer and the spring on the fuel pin? Thanks in advance.

I have just completed installing a 5.9 Cummins with 518 tranny into a Ford F250. Is it possible to run this transmission without the pcm? I have read threads mentioning taking the pcm out and using a switch or hobbs for the OD but not sure what to do with the connections for the thermal switch and...

I am replacing my 727 with a 47 RH and the 3.07 gears with 3.73s I have a Dana 70 out of a 96 CTD and I want to replace the drum brakes with discs. anyone done this ,

So im new to this site my name is zack and this is my first diesel i own, its a 91 cummins i/c in a 94 ford f350 with a zf-5 speed trans. i got it all installed but it wont start i checked the timeing and re-check it and had my pump dialed in and tryed 2 other pumps! i get foamy fuel at the...

Like title says, where can I get those clips that hold the door panel on?

The old VE would idle but no throttle, I didn't want to fool with it...so I put on another VE from a spare motor. This one started once, had a low rough idle, I shut it down....and now it will not refire. There is air in the lines every time I crack them loose at the injector. Doesn't even try...

Do they make a bolt on electric fan kit for our trucks? If not what cfm fan would i need to get and how hard are they to wire up ?

Ok, here we go. I recently purchased a 92 W250 automatic trans with only 61K miles on it, it sat for a long time. The truck's been running like a champ until a few days ago, when I noticed it seemed to not have as much power when I gave it some throttle. I was getting on the highway yesterday and...

i have a 89 non i/c and a few times a month. as i drive down the road the wait to start light will start blinking. it will continue to blink untill i shut the truck off. does anyone have any ideas or had this issue yourself. thanks

Hey guys, I want to bounce a scenario off of you, I’m looking for advice, wisdom or ideas. I am working on the truck in my signature and did the power mods in May of this year with the exception of bumping the timing, I did yesterday. It has 144k miles on it and when I bought the truck it only...

anyone runnin a set of their 6X16's? im lookin into a set but i wanna see some comments on them if possible. thanks guys! lance

I know I need to just search, but I got my buddy on the phone. I'm so confused now I've got a 92 i/c motor and thought that i read that when cummins went to i/c on their motors the switched to 7mm bore heads, from 9mm bore heads, because 9mm heads were prone to cracking at the bigger bore...

So, I'm tuning my cummins powered excursion and I feel like I'm not getting all my cummins has to offer. Motor has a 180hp pump from a buss and an air to water aftercooler. Stock injectors (1989 non ic) and was told these injectors would support up to 400hp??? 1. Full power screw maxed out....

ok so i popped the hood on the cummins i just bought was gettting ready to turn up the pump when i realized that the boost line going into the top of the afc was gone!!!! where would i find one of those i need the banjo bolt also

I have a 1993 Cummins 4x4 with the 5 speed manual tranny. It's always seem like I was going a lot faster than what the speedo is reading so I verified it with my GPS. I'm about 15 mph off when the speedometer reads 50 (gps says I'm going 65). I'm running 265/85/R16 tires. Is there any way to...